I’m a noob at 3D printing— I got my Ender3 S1 a little under a month ago. I’ve had great success on multiple prints using mostly default settings, up until last week. I had adhesion problems and was told it was likely my nozzle. I tried a spare nozzle and my next two prints were perfect. Since then I’ve had nothing but messy, blobby unsuccessful prints. More concerning, the prints are sticking to the bed so badly that all I can do is brutally scrape the PLA off. I’ve tried using iso alcohol but it doesn’t make much of a difference. I’ve heard acetone can damage the bed, and I don’t want to make it worse if it’s salvageable.

  1. Is my bed cover completely ruined?
  2. What should I do to prevent this in the future?

Thanks in advance. This is my first post on Lemmy and it’s exciting to see how quickly this community is growing!

  • bigredgiraffe@lemmy.world
    link
    fedilink
    English
    arrow-up
    6
    ·
    1 year ago

    I can’t quite tell from the photo but I f you aren’t using any glue try using some magigoo or something, seems counterintuitive I know but it helps it release from my experience.

    I would also heat your bed up to as high as it will go (I don’t have an wonder but 70 or 80 or something) which will soften the PLA and probably make it easier to get off, that has always helped me in the past.

  • CmdrShepard@lemmy.one
    link
    fedilink
    English
    arrow-up
    4
    ·
    1 year ago

    I wonder if your z offset is too low and the nozzle is too close to the bed. Also I can’t help but notice your bed looks really dirty (glue? hairspray?) Try resetting the z offset and using a dash of hairspray after cleaning the bed. Try scrubbing with dish soap and water before coming back with some IPA. In my experience the Z offset is the biggest factor for a consistent first layer. Not sure how it’s set on an Ender, but I put a receipt under the nozzle and lower it down til I feel some friction and then set it in Klipper.

  • ShadowCatEXE@lemmy.world
    link
    fedilink
    English
    arrow-up
    4
    ·
    1 year ago

    What are your print settings? Nozzle temp, bed temp, how close is the nozzle to the bed on the first layer, etc?

    • tylenol3@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      arrow-down
      1
      ·
      1 year ago

      200°/60°, and my Z offset is -2.71. Is this the same as first layer height?

      • SzethFriendOfNimi@lemmy.world
        link
        fedilink
        English
        arrow-up
        8
        ·
        1 year ago

        Try printing a 1 layer thick print to work out the Z offset

        For example in Cura I’ll import a cube, the scale it to be X: 40mm Y: 40mm Z: .25mm

        Set your initial layer flow to something like 105%

        Give that a print and see how the gaps line up.

        What you’re going for is what can be seen here in the Example section from the great Ellis’s tuning site (I highly recommend checking it out as you get more comfortable since it may be a little too in-depth if you’re just starting)

        https://ellis3dp.com/Print-Tuning-Guide/articles/first_layer_squish.html

        You want just enough “squish” that the each layer lines are touching to bond but not so much that it has to be pushed up and around the nozzle.

        Basically you’ll print that, and the back the nozzle away from the bed until you get the right spot.

        Get that right and you’ll find it gets easier to get successful prints

        • tylenol3@lemmy.worldOP
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          Thank you! This is exactly what I needed. I’ve ordered a replacement surface and I will go through this all on the weekend.

          I really appreciate you taking the time to help. Cheers!

          • SzethFriendOfNimi@lemmy.world
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            It may be scuffed but you can try and clean it up.

            Worst case you figure out how to get the nozzle just right on an unaffected piece before you get the new surface.

            You’ll have to slightly adjust the offset anyway since the new surface won’t be exactly the same but you can get much closer to it being right.

            And, worst case, err on the side of being too far and down dial it in closer

            • tylenol3@lemmy.worldOP
              link
              fedilink
              English
              arrow-up
              2
              ·
              1 year ago

              This is what I was thinking too. It is so stuck it will take a couple hours to get it all off, but at least I can test with it.

              One thing that worries me is that I had so many successful prints with exactly the same settings and filament I don’t know how it got this bad. I’m hoping I can prevent the same mistakes next time so I don’t ruin another surface.

              • SzethFriendOfNimi@lemmy.world
                link
                fedilink
                English
                arrow-up
                1
                ·
                1 year ago

                Wouldn’t hurt to check that the bed springs are not loose, belts have good tension, etc.

                But unless it’s really bad I bet your print surface is usable.

      • Shdwdrgn@mander.xyz
        link
        fedilink
        English
        arrow-up
        4
        ·
        1 year ago

        FYI, your Z-offset is really meaningless here. You have to calibrate the gap between your nozzle and bed, and you have to calibrate that for all four corners of the bed to be identical. THEN you have to determine if your bed is truly flat or if the center of the bed is higher/lower than the corners. And before starting any of that calibration, you need to make sure the springs under all four corners are tight (usually within 1 turn of completely closed) and then adjust your Z switch to match that position, otherwise you’ll be re-leveling your bed after every few prints. (It occurs to me your machine may not actually HAVE a Z switch, but you still want the springs compressed pretty tightly.)

        Yes yes, you have auto bed leveling built into your printer. Sorry to tell you, that doesn’t really mean anything except you have to wait for it to calibrate before every print, when if you just learn to calibrate it manually then you shouldn’t have to touch it again except maybe checking it every 6-12 months. In reality an ABL can only compensate so much, and if your bed isn’t level to begin with then the ABL calibration will cause your printer to be constantly adjusting the Z axis for each layer and your prints won’t be as smooth as they could be, and might not even be as strong. You want the bed to be level with the printer frame so that ideally the Z axis should never have to adjust when printing each layer.

        As for your goal in the nozzle gap… If your first layer is 0.20mm thick then you want a little squish, so you’re probably going to be shooting for around 0.15mm of actual gap. This is where a set of digital calipers comes in handy. Find one of the many first-layer test prints and give that a run (you probably need to find out how to disable your ABL for this). After it prints, you should have five small circles or squares in the corners and center. Measure the thickness of each, and look closely at them. Notice the individual strands of filament running through each piece. Can you see gaps between these strands? Can you pull it apart in your fingers? Then your nozzle gap is too large and the nozzle should be closer to the bed. Alternatively, is the piece solid, but very rough on the top? If so, your nozzle is likely too close to the bed. Your goal here is to get test prints that are smooth on top but will not come apart. When you have manually calibrated your bed leveling correctly, the ABL should calculate a Z offset of nearly zero.

        My quick estimate of what is causing problems with your prints sticking so badly to the bed – The nozzle is way too close to the bed, so close that the ABL cannot compensate, and the heat is literally fusing the filament with the bed. I can also see where you’ve had to scrape previous prints so hard to get them loose that you left marks in the bed, which is another sign that the gap was too small. Yeah it may be a lost cause at this point, but that’s why beds are replaceable. Learn what mistakes you made and ask questions sooner with the next bed. There is a huge learning curve to get started with 3D printing and you will certainly make other mistakes as you go – don’t worry, we all do it – but you can avoid some things by reading a lot of posts in these groups to see where others failed. Until you reach the level of physically modifying your printer, damaging the bed will likely be one of the worst things that happens (I destroyed my original controller board because I changed one of the steppers and forgot to modify the wire). Hang in there, you’ll get it figured out!

    • peekaboo@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      It’s counterintuitive at first, but using hairspray or 3DLac can really help to prevent the print sticking too much. Or can help it stick more, if needed, just like magic. But weird that it happens to the OP with PLA, usually PETG is the problematic material that sticks too much, not PLA.

  • BlondieBuff@kbin.social
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    I can’t help you with the quality of the prints, but I’ve found that sticking the bed and print into the freezer for 2-3 mins will help it pop off easily.

  • nate3D@kbin.social
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    I think your z-offset might be too low. Looks the the nozzle might be too close to the bed for the first layer. It should “place” the first layer down, not “squish” it.

  • Flaky_Fish69@kbin.social
    link
    fedilink
    English
    arrow-up
    3
    ·
    edit-2
    1 year ago

    Bring your bed temperature up to about 80/90 c. This will soften the pla (it becomes rubbery and stretchy,)

    Double check your z height- but the bed leveling screws in the middle of their range, Center the nozzle on the bed and calibrate offset there. Then level the corners to the nozzle.

    Keep in mind the bed might not be flat- it is a creality if that’s the case the best thing is to set up auto leveling with mesh/UBL. (Might have to upgrade the board for UBL… the BTT boards are pretty handy and they have drop ins for them)

  • Tefinite Dev@lemmy.world
    link
    fedilink
    English
    arrow-up
    3
    arrow-down
    1
    ·
    1 year ago

    This might be dumb after my first print on the ender 3 I couldn’t get the petg raft totally off the bed it came with. So, I just left it. I figured it was an easy way to adjust the bed height and it printed like a champion after that. Now I have a glass bed and a CR touch which helps a lot with the start

  • rambos@lemmy.world
    link
    fedilink
    English
    arrow-up
    2
    ·
    1 year ago

    Looks kinda bad, but once you dial in your settings, you can try printing large part over that area and hope they come off together. Using glue or hairspray can help, but I dont recommend that since its not needed for pla. With thin layer of glue you can probably keep using that bed tho. Better start with too high nozzle-bed distance and decrease in baby steps

  • TwanHE@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    This looks like the stock ender 3 S1 bed. If you get the prints off you might actually pull the texture of the metal flex plate. Mine lasted a few days before I had multiple holes.

    I got a textured PEI plate and I can’t complain, prints self release when the plate cools and it doesn’t have any defects after almost a year and about 100kg of filament.

    • tylenol3@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Just for reference, what sort of plate did you replace it with? I’m waiting on a Creality glass PEI plate that should be here soon and I’m hoping it will be better. Still not sure how this happened in the first place but from what I read it looks like the print head was too close to the plate and it ground PLA into the bed. I was using the same settings as always and I trammed and levelled before my first print. It seems to have done this every time I tried to print this particular object— Is it possible the actual gcode from Cura could cause this?