• SternburgExport@feddit.de
    link
    fedilink
    arrow-up
    60
    arrow-down
    5
    ·
    1 year ago

    Cables are fine until that stupid clip breaks off and every nudge unplugs the fucking cable ever so slightly that it doesn’t work but you can’t see it.

    • saigot@lemmy.ca
      link
      fedilink
      arrow-up
      10
      ·
      1 year ago

      It’s pretty easy to crimp a new one back on, and even easier with a 30 dollar tool.

    • oʍʇǝuoǝnu@lemmy.ca
      link
      fedilink
      arrow-up
      8
      ·
      1 year ago

      Easy fix with a tight layer of electrical tape to act as a wedge. You can also shove a toothpick in the top for extra staying power.

    • PM_Your_Nudes_Please@lemmy.world
      link
      fedilink
      arrow-up
      0
      ·
      edit-2
      1 year ago

      Get a crimp tool and a 50-pack of connectors. If one breaks, it takes all of 60 seconds to re-crimp the end and you’ll only lose about an inch of cable length.

      I re-cabled my entire apartment when I first moved in. Best decision I ever made. I just used the existing Cat5 lines to pull my Cat6a instead. Apartment got a free upgrade to Cat6a (which they never even knew about, because I wasn’t going to lose a deposit over something stupid like “unapproved upgrades”) and I got my tasty gigabit.

      I was trying to download Red Dead Redemption 2. It was like 120GB, and was going to take hours at 10Mbps on the existing Cat5. I quickly said “fuck that, I can run new lines in 45 minutes and have the download done in 20 minutes with gigabit.” Sure enough, about an hour later, I was playing my game.

      • kklusz@lemmy.world
        link
        fedilink
        arrow-up
        0
        ·
        1 year ago

        I have zero experience with networking hardware. How hard is it to recable an apartment for a newb like me? How does that even work, do I gotta pull wires out of the walls?

        • sznio@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          No pulling wires from walls, just cutting the ends off and installing new connectors. Might not be enough in every case though.

          Crimping took me like 5 attempts to get right when I learned it in school.

        • PM_Your_Nudes_Please@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          Replacing connectors is east, but won’t solve your problem if the issue is bad cables in the walls. Pulling new cables entirely depends on how well they were installed. A lazy install will actually be much easier to replace, because a lazy installer won’t bother stapling cables in place. They’ll just run the cables across the attic/crawl space and leave it where it lands.

          If you’re lucky and got a lazy installer, then you can be equally lazy; The old cable in the wall is going to be your pull line for your new cable. Step 1 is figuring out which lines are which. This is easier with something like a cable sniffer, but there are a few ways to do it. But assuming you know which cables are which, the rest is fairly straightforward.

          Use electrical tape to affix the old cable to the new one. Just make a bend on each cable, hook the resulting bends together, then wrap them tightly with electrical tape. The bends hooked together allow the cable to hold the strain, rather than the adhesive on the tape. And you want to use electrical tape because it stretches. Pulling it tight when you wrap ensures that the tape will compress the cables with every wrap. You also want to try to make the connection as “smooth” as possible, so it won’t snag on anything when you pull it.

          Now that the old cable is attached to the new, just grab the other end of the old cable and start pulling. It’ll drag the new cable through the wall for you as you pull it out of the wall. Fair warning this is much easier if you have someone feeding the new cable in as you pull, to ensure it doesn’t snag on anything as it enters the wall. It also only reliably works on installs without a lot of bends and corners; Every corner you have to pull around is another potential corner to get snagged on. If you get snagged, sometimes pulling it backwards (tugging on the new cable entering the wall) can help you reset to try again. But sometimes there’s no replacement for good old fashioned legwork; If you get really stuck, or your tape comes undone, or your cable breaks from the strain, you may need to go crawling around your attic to fix it. This is a fast method, but it’s not 100% reliable.